SEAT Leon III (5F) 2.0 TFSI OPF (190 hp) remapping
- Fuel
- Petrol
- Years
- 2012 - 2019
- ECU
- Bosch MG1CS001 / Bosch MG1CS111
- Method
- Through the OBD port
Stage 1
SEAT Leon III (5F) 2.0 TFSI OPF (190 hp)
Power
+50 hp +26 %
Torque
+100 Nm +31 %
| Power | Torque | |
|---|---|---|
| Stock | 190 hp | 320 Nm |
| Stage 1 | 240 hp | 420 Nm |
| Gain | +50 hp | +100 Nm |
E85 FlexFuel conversion
SEAT Leon III (5F) 2.0 TFSI OPF (190 hp)
Ethanol ECU tuning: a FlexFuel ECU map to run on E85 Superethanol, cheaper at the pump, with no add-on module.
This ECU tune adapts the engine to Superethanol, with no claimed power gain.
How the remap works
- You order for your vehicle Engine and VIN: the map is prepared for your ECU.
- You receive the REPROG dongle A Bluetooth box that plugs into the OBD port under the dashboard.
- The app saves the stock map With MyFlasher (iOS, Android), the dongle reads and keeps the factory map.
- You flash in a few minutes The Dynaparts map is loaded; going back to stock remains possible at any time.
Other Leon III (5F) engines
| Engine | Stock | After remap | Gain | Details |
|---|---|---|---|---|
| 1.5 TSI (130 hp) Petrol E85 compatible | 130 hp200 Nm | 175 hp300 Nm | +45 hp+100 Nm | |
| 1.4 TSI (150 hp) Petrol E85 compatible | 150 hp250 Nm | 180 hp300 Nm | +30 hp+50 Nm | |
| 1.8 TSI (180 hp) Petrol E85 compatible | 180 hp250 Nm | 220 hp320 Nm | +40 hp+70 Nm | |
| 2.0 TFSI OPF (190 hp) Petrol E85 compatible | 190 hp320 Nm | 240 hp420 Nm | +50 hp+100 Nm | This page |
| 2.0 TSI Cupra (265 hp) Petrol E85 compatible | 265 hp350 Nm | 350 hp460 Nm | +85 hp+110 Nm | |
| 2.0 TSI (280 hp) Petrol E85 compatible | 280 hp350 Nm | 350 hp460 Nm | +70 hp+110 Nm | |
| 2.0 TSI Cupra SC (280/290 hp) Petrol E85 compatible | 290 hp350 Nm | 350 hp460 Nm | +60 hp+110 Nm | |
| 2.0 TSI Cupra SC FAP (290cv) Petrol E85 compatible | 290 hp380 Nm | 340 hp460 Nm | +50 hp+80 Nm | |
| 2.0 TSI Cupra ST (280/290 hp) Petrol E85 compatible | 290 hp350 Nm | 350 hp460 Nm | +60 hp+110 Nm | |
| 2.0 TSI Cupra SC (300 hp) Petrol E85 compatible | 300 hp380 Nm | 350 hp460 Nm | +50 hp+80 Nm | |
| 2.0 TSI Cupra ST (300 hp) Petrol E85 compatible | 300 hp380 Nm | 350 hp460 Nm | +50 hp+80 Nm | |
| 2.0 TDI (150 hp) Diesel | 150 hp320 Nm | 185 hp420 Nm | +35 hp+100 Nm |
All Leon III (5F) engines Parts compatible with this vehicle
Frequently asked questions
How does a remap with the REPROG pack work?
You plug the REPROG by Dynaparts Bluetooth OBD dongle into the vehicle's OBD port and install the MyFlasher app (iOS or Android). The dongle reads and saves the stock map, then loads the Dynaparts map for your engine. Flashing takes a few minutes, with no dismantling.
Why give my vehicle's VIN?
The map is prepared for your engine and ECU. The VIN (field E of the registration document) lets us check the exact vehicle version before shipping.
Can I go back to the stock map?
Yes. The stock map is saved during the first read and can be restored at any time from the app, in a few minutes.
What is the difference between Stage 1 and the E85 pack?
Stage 1 optimises injection, ignition and boost management on the original fuel. The E85 pack installs a FlexFuel map to run on E85 bioethanol, cheaper at the pump, without an add-on box.
Are the stated gains guaranteed?
Indicative figures measured on a stock vehicle in good maintenance condition: they may vary depending on engine condition, fuel and measurement conditions. ECU tuning changes the vehicle's specifications: remember to inform your insurer.
Indicative figures measured on a stock vehicle in good maintenance condition: they may vary depending on engine condition, fuel and measurement conditions. ECU tuning changes the vehicle's specifications: remember to inform your insurer.